English
welcome

Mother's Day Bracelet Project

Product Details

Quantity of Items Needed


24 Swarovski Bicone 5328 4mm Aquamarine (A)

24 Swarovski Bicone 5328 4mm Sapphire (B)

24 Swarovski Bicone 5301 4mm Blue Zircon (C)

42 Round Bead 3mm Sterling Silver (D)

6 Crimp Tube Seamless 2x2mm Sterling Silver (E)

6 Crimp Cover 3mm Sterling Silver (F)

27\" Beadalon Wire .015\" 15ft Silver Plated 19 Strand (G)

1 Three Strand Plunger Clasp 22x12mm Sterling Silver (H)

1 \"Mom\" Heart Charm - 13x16mm Sterling Silver (I)

2 Jump Ring Round Open 4mm Sterling Silver (J)

1 Jump Ring Round Closed 5mm Sterling Silver (K)

1 Sterling Silver Rondell Dividers - 5 Hole (L)

1 Pkg. of India Seed Bead Silver Lined 6/0 Aqua (M)

1 Pkg. of India Seed Bead Silver Lined 6/0 Blue (O)

1 Pkg. of India Seed Bead Inside Color 6/0 Aqua (P)


Instructions.


1) Take one 9\" length of G

2) Start your beadwork.

1 Sterling Silver Seamless Round Beads (3mm)

1 Sterling Silver Seamless Crimp Tube (2x2mm)

1 Sterling Silver Seamless Round Beads (3mm)

3) Take one half of H and the end of the beaded length of G. Thread the wire through one of the holes, then around and back through the three beads. Pull the wire until the beads are close to the clasp (don\'t make it too tight, as you want some movement when the strand is finished). Crimp E with a plier. If there is any wire tail sticking out after threading it back through all the beads, cut that with plier. Repeat with the two remaining lengths of G.

4) Now you\'re ready for the beading pattern. Each of the strands will start on a different section of the pattern. (You can have all the strands start on the same section if you like) Here are the sections (Completely finish each strand before threading the next)

Section #1 Section #2 Section #3 Section #4

4 -AC\'s (Bicones) 1 - Seed Bead 4 - Seed Beads 1 - AC (Bicone)

1 - AC (Bicone) 1 - Seed Bead

1 - Seed Bead 1 - AC (Bicone)

1 - AC (Bicone) 1 - Seed Bead

(In the picture, the Aqua strand started with section #4, and the Blue Zircon and Sapphire strands started with section #2) Place one D between each section. After the sixth section, thread the wires through the 1st, 3rd, and 5th holes of L.

5) After stringing strand #1,

Start your beadwork.

1 Sterling Silver Seamless Round Beads (3mm)

1 Sterling Silver Seamless Crimp Tube (2x2mm)

1 Sterling Silver Seamless Round Beads (3mm)

6) Take the other half of H and thread the end of G through one the same number hole that you used on the other half of H. Then thread the wire around and back through the three beads. Pull until all the beads are close to the clasp (remember not snug). Crimp E. If there is any wire tail that is sticking out after threading the wire back through the three beads, cut it off with plier.

7) Repeat the last step for the two remaining strands.

To Finish.
8) Take two pliers and open the two J. Attach one to a hole on the end of H and K. Close this jump ring. With the other open J, attach to I and K. Close this jump ring. 

You May Also Like

About us |  Contact us |  Term of us |  Attention & Care |  Discount Policy |  Return Policy |  Article Details |  How to Pay |  SiteMap

Milky Way Jewelry Ltd. Group: Gets.cn | Beads.us

Copyright © 2013 Milky Way Jewelry Ltd. All rights reserved.