English
welcome

Fashion Jewelry Set

Product Details

Materials:

1 Pkg. Gold Lined Crystals, 4mm

1 Pkg. Gold Lined Crystals, 6mm

1 Pkg. Lt Colorado Topaz Swarovski Crystals, 4mm

1 Pkg. Lt Colorado Topaz Swarovski Crystals, 5mm

1 Pkg. Lumi Rose Pony Beads

1 Pkg. MET Gold Pony Beads

1 Pkg. Silver Lined Gold Pony Beads

1 Pkg. Gold, Round Pearls, 8mm

1 Pkg. G/P Wire, 22 Gauge

1 Spool of Medium SoftFlex

1 Pkg. G/P Kidney Style Ear Wires

1 Pkg. G/P Jump Rings, 4mm

1 Pkg. G/P Crimp Beads

1 Pkg. Antique Gold Small Toggle Clasp with Twist Bar

1 Pkg. Silver Lined Crystal Cube Seed Beads, 4mm

1 Pkg. Gold Miyuki Mix Seed Beads

Tools you will need:  

Crimping Pliers

Flat Chain Nose Pliers

Round Nose Pliers

Side Cutters

Directions:  

Necklace Directions:  

The finished length will be about 17.  The necklace should fit like a choker, so if you would like it longer, you may add more Silver Lined Crystal Cube Seed Beads on the ends.

Step 1.  Cut a strand of SoftFlex about 18 long.

Step 2.  String the SoftFlex through 1 Crimp Bead, then through the loop of one end of the Toggle and then back through the Crimp Bead. Snug the Crimp Bead up to the Toggle and crush the Crimp Bead. Trim the end.

Step 3.  String the following beads:

1 Silver Crystal Cube Seed Bead

One 4mm Topaz Crystal

1 Silver Crystal Cube Seed Bead

1 Silver Lined Gold Pony Bead

1 Lumi Rose Pony Bead

One 5mm Topaz Crystal

1 Lumi Rose Pony Bead

1 Silver Lined Gold Pony Bead

1 MET Gold Pony Bead

1 Lumi Rose Pony Bead

One 6mm Gold Lined Crystal

1 Lumi Rose Pony Bead

1 MET Gold Pony Bead

1 Silver Lined Crystal Cube Seed Bead

One 4mm Topaz Crystal

1 Silver Lined Crystal Cube Seed Bead

1 Pearl

Repeat the above pattern 4 more times.

Step 4.  Repeat the pattern from Step 3 once, leaving out the Pearl at the end.

Step 5.  Repeat Step 2 with the other end of the Toggle Clasp.

Bracelet Directions:  

Step 1.  Cut 3 strands of SoftFlex, each about 10 long.

Step 2.  String 1 strand of SoftFlex through a Crimp Bead, then through the loop of one end of the Toggle Clasp and back through the Crimp Bead. Crush the Crimp Bead and trim the excess.

Step 3.  Repeat Step 2 with second and third strands.

Step 4.  String the following beads onto the middle strand:

1 Pearl

1 Silver Crystal Cube Seed Bead

One 4mm Topaz Crystal

1 Silver Crystal Cube Seed Bead

1 Silver Lined Gold Pony Bead

1 Lumi Rose Pony Bead

One 5mm Topaz Crystal

1 Lumi Rose Pony Bead

1 Silver Lined Gold Pony Bead

1 MET Gold Pony Bead

1 Lumi Rose Pony Bead

One 4mm Gold Lined Crystal

1 Lumi Rose Pony Bead

1 MET Gold Pony Bead

1 Silver Lined Crystal Cube Seed Bead

One 4mm Topaz Crystal

1 Silver Lined Crystal Cube Seed Bead

Step 5.  Repeat the above pattern 2 more times.

Step 6.  Repeat Step 2 with the other end of the Toggle Clasp.

Step 7.  For the other 2 strands of your bracelet (the outside strands), you will string just Gold Miyuki Seed Beads in any order.  (Note:  You will want to be sure that the length of all three strands matches up)

Step 8.  Repeat Step 2 with these 2 strands and the other end of the Toggle Clasp.

The finished length will be about 7 1/2.

Earring Directions:  

Step 1.  Cut a length of Gold Wire about 6 long.

Step 2.  Spiral the Wire around a pen or a pencil about 5 times to give the earring its shape.

Step 3.  Take the Wire off the pencil and stretch it out (Note: the farther that you stretch it, the easier the beads will slide on.  If, in making the earrings, the Wire loses some of its shape, you will be able to re-shape it, as desired, once all the beads are strung on).

Step 4.  Bend about 3/16 piece of Wire 90 degrees. Using Round Nose Pliers, bend the piece of Wire into a loop, and close tightly.

Step 5.  Place the following beads onto the Wire:

1 MET Gold Pony Bead

One 6mm Gold Lined Crystal

1 MET Gold Pony Bead

1 Lumi Rose Pony Bead

One 5mm Topaz Crystal

1 Lumi Rose Pony Bead

1 Silver Lined Gold Pony Bead

1 Silver Lined Crystal Cube Seed Bead

1 Silver Lined Gold Pony Bead

1 MET Gold Pony Bead

One 6mm Gold Lined Crystal

1 MET Gold Pony Bead

1 Lumi Rose Pony Bead

One 4mm Topaz Crystal

1 Lumi Rose Pony Bead

1 Silver Lined Gold Pony Bead

1 Silver Lined Crystal Cube Seed Bead

1 Silver Lined Gold Pony Bead

Step 6.  Once all the beads are on the wire, make a small loop at the bottom of the wire to keep them from falling off.

Step 7.  Using a Wire Cutter cut off the excess Wire, leaving 3/16. Using Flat Nose Pliers, bend the 3/16 piece of Wire 90 degrees. Using Round Nose Pliers, bend the piece of Wire into a loop, and close tightly.

Step 8.  Twist open a Jump Ring and insert it into the loop that you just made with the Wire, and then the Ear Wire.  Twist the Jump Ring Closed.

Repeat Steps 1 through 7 for the second earring.  Enjoy!

You May Also Like

About us |  Contact us |  Term of us |  Attention & Care |  Discount Policy |  Return Policy |  Article Details |  How to Pay |  SiteMap

Milky Way Jewelry Ltd. Group: Gets.cn | Beads.us

Copyright © 2013 Milky Way Jewelry Ltd. All rights reserved.